Category
Most Popular Products
AP 33 ANALOG MULTITESTER – SANWA
$0.00
Pocketable Analog Multimeter / Analog Multitester
- Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
- The test leads can be winded up and stored
- Battery check function has 2 ranges of 1.5V/9V
- Shock absorbing rubber that is robust against falling
AP33 Analog Multitesters / Analog Multimeter – Slim compact AMT
Small pocket size
BASIC FEATURES:
- Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
- The test leads can be winded up and stored
- Battery check function has 2 ranges of 1.5V/9V
- Shock absorbing rubber that is robust against falling
SAFETY:
IEC61010 CAT.III 300V CAT.II 500V
SPECIFICATIONS:
Function | Measuring range | Tolerance |
---|---|---|
DCV | 10/50/250/500V(2kΩ/V) | ±5% of full scale |
ACV | 50/250/500V(2kΩ/V) | ±5% of full scale |
Battery check | 1.5V/9V | ̶ |
DCA | 25m/250mA | ±5% of full scale |
Resistance | 10k/1MΩ | ±3% of arc |
Frequency characteristic | AC50V range or lower 40Hz to 10kHz: frequency response within ±3% |
Battery | R03(AAA battery)×1 |
Built-in fuse | F0301 Φ5x20mm 0.5A/250V 300A Glass fuse |
Size/Mass | H126×W87×D30mm/Approx. 185g |
Test lead length/Pin tip | Approx. 0.6m/13mm |
※The value in ( )at DCV and ACV is input resistance
Related products
-
AU-32 / AU-31 ANALOG MULTITESTER – SANWA
$0.00Add To QuoteAU-32 / AU-31 Analog Multitesters High input impedance Auto range, High input impedance BASIC FEATURES: Auto range selection (V, Ω) Auto polarity High input impedance 1〜10MΩ Series capacitor input ※AU-31 ACV only Auto 0Ω adjustment Inner battery check DC / AC auto selection ※AU-32 only 5 ranges DC / AC current ※AU-32 only Bandwidth : …
-
YX – 361TR ANALOG MULTITESTER – SANWA
$0.00Add To QuoteVariety of measurement functions by using 24-contact switch
- Employing 24-contact switch and plus alpha function enable you to enjoy a total of 33 functions
- Zero center meter for ± DCV measurement
- With LED for continuity check
- With OUTPUT measurement terminal (series capacitor inserted)
- Battery check
- DC current gain (hFE) of transistor can be measured by using separately available hFE connector
-
EM7000 ANALOG MULTITESTER – SANWA
$0.00Add To QuoteHigh sensitivity for measurement of lower capacitance
- High-sensitivity FET electronic tester with high input resistance (2.5M – 12MΩ for DCV) and 0.12μA range (DC current)
- Frequency response against 40Hz to 1MHz of sine wave (AC low voltage)
- Measurement of P-P value (Peak to Peak value) of square wave pulse (duty cycle 20% or higher)
- Wide range resistance measurement from 0.2Ω to 200MΩ
※Zero adjustment needs to be performed before measurement, since the instrument is an electronic tester.
-
CP – 7D ANALOG MULTITESTER – SANWA
$0.00Add To QuoteWide scale with mirror for easy reading of measured values
- Wide scale with mirror
- Fixed test leads for safety and operability
- Employs metal oxide film resistors that are high precision, heat resistant, smokeless
- Battery check
- Internal circuit protection with fuse and diode
-
SP – 18D ANALOG MULTITESTER – SANWA
$0.00Add To QuoteCase and instrument in one body, that brings you a convenience to carry and store
- Resistance up to 200MΩ can be measured under the low voltage(3V)
- Capacitance measurement from 0.01μF to 1000μF
- Resistance measurement that has 3V of the terminal voltage allows to check an LED
- Battery check
- Front panel protection cover that also works as a stand
Contact Us
For Quotes:
email: info@bhumika.ca
phone: 613-619-0894