Based in Canada, we deliver across North America

info@bhumika.ca

Test and Measurement Solutions

Archives: Shop

Showing 1–48 of 83 results

  • AP 33 ANALOG MULTITESTER – SANWA

    Pocketable Analog Multimeter / Analog Multitester

    • Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
    • The test leads can be winded up and stored
    • Battery check function has 2 ranges of 1.5V/9V
    • Shock absorbing rubber that is robust against falling
    Add To Quote
  • AU-32 / AU-31 ANALOG MULTITESTER – SANWA

    AU-32 / AU-31 Analog Multitesters High input impedance Auto range, High input impedance BASIC FEATURES: Auto range selection (V, Ω) Auto polarity High input impedance 1〜10MΩ Series capacitor input ※AU-31 ACV only Auto 0Ω adjustment Inner battery check DC / AC auto selection ※AU-32 only 5 ranges DC / AC current ※AU-32 only Bandwidth : …

    AU-32 / AU-31 ANALOG MULTITESTER – SANWARead More

    Add To Quote
  • CAM600S CLAMP METER – SANWA

    Analog type, AC current measurable max. 600A

    • Long analog pointer with “pointer lock” function
    Add To Quote
  • CD721 CD731 DIGITAL MULTIMETER – SANWA

    NOTE: This item has been discontinued by SANWA. We have a few units that’s available in stock, and are available at great prices.

    Add To Quote
  • CD732 DIGITAL MULTIMETER – SANWA

    Multifunction

    High-speed bar graph & Cont.buzzer with LED

    • 6000 counts
    • Using fire-retardand materials for main unit case and circuit board
    • Wide-range capacitance measurement
      (0.01nF to 3999μF)
    • Safety cover for 6・15A terminal
    • Protective holster with wall hanger and lead holster
    • Auto power save (16mn.) (cancelable)
    Add To Quote
  • CD770 DIGITAL MULTIMETER – SANWA

    New standard

    Capacitance and frequency can be measured too

    • 4000 counts
    • Easy to read large LCD
    • Thermo plastic elstomer, high resistance against drop shock
    • Safety cap on current terminal
    • Auto power off (30min.)(cancelable)
    Add To Quote
  • CD771 DIGITAL MULTIMETER – SANWA

    Multifunctional new standard

    Backlight & Cont.buzzer with LED

    • 4000 counts
    • Easy to read large LCD with backlight
    • Large breaking capacity fuse 30kA
    • 1.5V battery check function
    • Thermo plastic elstomer, high resistance against drop shock
    • Safety cap on current terminal
    • Auto power off(30min.)(cancelable)
    Add To Quote
  • CD772 DIGITAL MULTIMETER – SANWA

    Ture RMS new standard

    Blacklight & Temperature measurement

    • 4000 counts
    • Easy to read large LCD with backlight
    • Large breaking capacity fuse 30kA
    • K type thermocouple temperature measurement -20℃ ~ 300℃
    • Thermo plastic elstomer, high resistance against drop shock
    • Safety cap on current terminal
    • Auto power off (30min.)(cancelable)
    Add To Quote
  • CD800a DIGITAL MULTIMETER – SANWA

    ALL-IN-ONE DMM

    Tough body cover

    • 4000 counts
    • Best accuracy 0.7%
    • Auto power off(30min.)(cancelable)
    • Low power ohm(input voltage 0.4V)at continuity range
    • Solid & portective body cover that can also be used as a tilt stand
    • Chip resister holder behind the body cover
    Add To Quote
  • CD800b DIGITAL MULTIMETER – SANWA

    ALL-IN-ONE DMM

    True RMS,Portalbe DMM

    • 6000 counts
    • MAX/MIN value recording
    • Auto power save (15min.)(cancelable)
    • Attachment body cover for protection
    • Best accuracy 0.8%
    Add To Quote
  • CD800F DIGITAL MULTIMETER – SANWA

    ALL-IN-ONE DMM

    True RMS, CAT.Ⅳ DMM

    • 6000 counts
    • MAX/MIN value recording mode
    • Auto power save(15min.)(cancelable)
    • Attachment body cover for protection
    • EF(Electric Field)detection
    • Best accuracy 0.8%
    Add To Quote
  • CP – 7D ANALOG MULTITESTER – SANWA

    Wide scale with mirror for easy reading of measured values

    • Wide scale with mirror
    • Fixed test leads for safety and operability
    • Employs metal oxide film resistors that are high precision, heat resistant, smokeless
    • Battery check
    • Internal circuit protection with fuse and diode
    Add To Quote
  • CX 506a ANALOG MULTITESTER – SANWA

    Capacitance measurement function with built-in transistor oscillator

    • Variety of measurement functions by using 26-contact switch
    • Capacitance measurement from 50pF to 2000μF
    • High input resistance 50kΩ/V (each range of DC3 to 300V)
    • DC polarity switchable
    Add To Quote
  • DCL 1000 CLAMP METER – SANWA

    Large diameter CT, AC current measurable max. 1000A

    • Lightweight approx. 290g
    • Large LCD
    • Easy to use large size data hold button
    Add To Quote
  • DCL 1200R CLAMP METER – SANWA

    Large diameter CT & DMM functions

    • Lightweight approx. 290g
    • Large LCD with backlight
    • Easy to use large size data hold button
    • Non-contact voltage detection function
    • Auto V/Ω detection
    Add To Quote
  • DCL 3000R CLAMP METER – SANWA

    ACA clamp meter with flexible CT

    • Flexibility facilitating conductor clamping even in narrow space
    • MAX/MIN value hold
    • Air-core coil for weight reduction
    • Auto power off (15 min./Cancelable)
    Add To Quote
  • DCL11R Clamp Meter – SANWA

    RMS mini clamp meter with backlight

    • Compact pocket size
    • Auto power off (15 min./Cancelable)
    Add To Quote
  • DCL31DR – Digital Clamp Meter – SANWA

    DC/AC RMS mini clamp meter with peak hold function

    • Compact pocket size
    • Auto power off (15min./Cancelable)
    Add To Quote
  • DCM-22AD CLAMP METER – SANWA

    Clamp Meters DC/AC

    DC / AC compact type & DMM functions
    NOTE: This item has been discontinued by SANWA. We have a few units that’s available in stock, and are available at great prices.

     

    Add To Quote
  • DCM-400 CLAMP METER – SANWA

    Low cost & DMM functions

    • 4000 counts, 42 segments analog bar graph
    • Frequency measurement by clamping and using test lead
    • Auto power off (30 min.)
    • Low battery power indication
    Add To Quote
  • DCM-400AD CLAMP METER – SANWA

    Suitable for automotive maintenance & DMM functions

    • 4000 counts, 42 segments analog bar graph
    • Auto power off (30 min.)
    • Low battery power indication
    Add To Quote
  • DCM-600DR CLAMP METER – SANWA

    Suitable for maintenance of vehicle, hybrid vehicle, EV & DMM functions

    • AC/DC current measurable max. 600A
    • Peak hold (Interval: 1ms)
    • Auto power save (30min./Cancelable)
    Add To Quote
  • DCM-60L CLAMP METER – SANWA

    Low cost & DMM functions
    NOTE: This item has been discontinued by SANWA. We have a few units that’s available in stock, and are available at great prices.

    BASIC FEATURES:

    • Measurable AC 0.1A〜600A
    • ACV & Resistance measurement
    • Small design & easy to carry
    • Data hold
    • Continuity check buzzer
    • Sampling rate : 2 times / sec.
    • AC frequency bandwidth : 50〜500Hz
    Add To Quote
  • DCM-660R CLAMP METER – SANWA

    Suitable for electric work and air conditioning & DMM functions

    • Inrush current measurement (within 100ms/above 10A)
    • MAX/MIN value hold
    • Frequency measurement by clamping and using test lead
    Add To Quote
  • DCM2000DR

    DC/AC current measurable max. 2000A, CAT.IV 1000V

    • Dual display shows voltage/current and its frequency
    • EF (Electric Field) detection
    • VFD (Variable Frequency Drive) frequency measurement
    • Low input impedance voltage measurement capable of attenuating the effects of ghost voltages
    • Peak hold (Interval: 5 ms)
    • Auto power save (30 min./Cancelable)
    Add To Quote
  • DCM60R Clamp Meter – SANWA

    Low cost & DMM functions

    • ACV & resistance measurement
    • Small design & easy to carry
    Add To Quote
  • DG 10 INSULATION TESTER – SANWA

    Insulation Testers Pocket size/Digital Suitable for high voltage insulation measurement at construction sites BASIC FEATURES: Test voltage DC500V / 125V Wide measurement range 1kΩ〜400MΩ High resolution 0.001MΩ(1kΩ) Data hold Auto power save (30min.) Sampling rate : 2 times / sec. for numeral disply, 20 times / sec. for bar graph SPECIFICATIONS:

    Add To Quote
  • DG34a DIGITAL MULTIMETER CLAMP METER – SANWA

    MΩ Tester

    Hybrid pocket size MΩ tester + clamp meter

    • 500V; 400MΩ
    • 250V; 400MΩ
    • 125V; 400MΩ
    • Lightweight approx. 160g
    • DCV/ACV measurement functions
    • DC/AC current measurable up to 100A
    • Test leads holder
    • U-shaped clamp sensor, 7mm thick
    Add To Quote
  • DG35a DIGITAL MULTIMETER CLAMP METER – SANWA

    DG35a  MΩ Tester Hybrid pocket size MΩ tester + clamp meter 500V; 40MΩ 250V; 40MΩ 125V; 40MΩ Lightweight approx.160g DCV/ACV measurement functions DCV/AC current measurable up to 100A Test leads holder U-shaped clamp sensor, 7mm thick Specifications DG35a Measuring rage Best accuracy Resolution MΩTest 40MΩ ±(3.0%+3) 0.01MΩ Test voltage 125/250/500V DCA 100A ±(2.0%+5) 0.1A ACA …

    DG35a DIGITAL MULTIMETER CLAMP METER – SANWARead More

    Add To Quote
  • DLC460F CLAMP METER – SANWA

    Multifunctional lo leakage clamp meter

    • Low-pass filter function cuts current value of high frequency
    • MAX/MIN value hold
    • Auto power save (30 min./Cancelable)
    • Leakage current measurement Resolution 0.01mA
    Add To Quote
  • DM 509S INSULATION TESTER – SANWA

    Analog single range

    500V/1000MΩ single range, Lightweight design

    • One-shot or continuous measurement push switch
    • DCV measurement range (DC60V)
    • Auto discharge function
    • Inner battery check range
    • Shoulder Strap
    Add To Quote
  • DM1009S INSULATION TESTER – SANWA

    Analog single range

    1000V/2000MΩ single range, Lightweight design

    • One-shot or continuous measurement push switch
    • DCV measurement range (DC60V)
    • Auto discharge function
    • Inner battery check range
    • Shoulder Strap
    Add To Quote
  • EM7000 ANALOG MULTITESTER – SANWA

    High sensitivity for measurement of lower capacitance

    • High-sensitivity FET electronic tester with high input resistance (2.5M – 12MΩ for DCV) and 0.12μA range (DC current)
    • Frequency response against 40Hz to 1MHz of sine wave (AC low voltage)
    • Measurement of P-P value (Peak to Peak value) of square wave pulse (duty cycle 20% or higher)
    • Wide range resistance measurement from 0.2Ω to 200MΩ

    ※Zero adjustment needs to be performed before measurement, since the instrument is an electronic tester.

    Add To Quote
  • HG 561H INSULATION TESTER – SANWA

    Digital 7 ranges

    “Smart style”7 ranges Insulation Resistance Tester

    • 15V; 21MΩ
    • 25V; 21MΩ
    • 50V; 21MΩ
    • 100V; 110MΩ
    • 125V; 110MΩ
    • 250V; 110MΩ
    • 500V; 110MΩ
    • Test voltage selection mode
    • LED level meter shows MΩ
    • East-to-read LCD with fixed decimal point
    • Automatic data hold function
    • Has a backlight that is convenient for measuring in a dark place and an LED light that illuminates your work site
    Add To Quote
  • KD 1 VOLTAGE DETECTOR – SANWA

    NOTE: This item has been discontinued by SANWA. We have a few units that’s available in stock, and are available at great prices.

    Detectors Voltage detector

    BASIC FEATURES:

    • Detect AC voltage safely
    • Lead-free
    • Fast and easy to use pen type
    Add To Quote
  • KD2 VOLTAGE DETECTOR – SANWA

    Voltage Detector

    Low Voltage Detector

    • Beeping and LED lighting upon detection
    • Switchable to measure cord or bare wire
    Add To Quote
  • KDP10 – Voltage Detector Supporter – SANWA

    Voltage Detector Supporter

    This Voltage Detector Supporter is intended to eliminate accidents caused by an erroneous cut of a live-wire cable for a commercial power’s alternate voltage (frequency: 50 Hz/60 Hz) by being attached to a manual cable cutter.

    • Attachable to your 7 or 8 inch pliers to warn before cutting live line
    • Detectable with gloves on
    • Long battery life, Approx. 5 months of battery life in standby mode
    Add To Quote
  • KIT – 8D DIY KITS FOR EDUCATION – SANWA

    Analog type

    Learning kit designed for measurement of small capacity electric circuits

    • Equipped with lightweight, small, high-sensitivity and shock resistant type band meter.
    • Basic functions include measurement of DCV, ACV, DCA and Ω. In addition, the battery check range allows inspection of 1.5V dry battery at an actual load (20Ω).
    • Direct-mount test leads ensure no need to worry about missing of leads. Convenient storage space within the main body available.
    • Panel protection cover equipped, also acts as a stand.
    • Hand strap convenient for carrying.

    * Sanwa assembly training kits have been developed for educational purpose. 

    Add To Quote
  • KP1 DIGITAL MULTIMETER – SANWA

    Volt Tester

    CAT.IV Volt tester

    • Self test-checking failures of LCD, disconnection of a lead wire
    • EF(Electric Field)detection
    • LCD with backlight & LED Light for dark place
    • Auto data hold
    • Auto power off(1min.)
    • Auto identification of AC or DC voltage
    Add To Quote
  • KS 1 3PHASE DETECTOR – SANWA

    Contact-type 3 phase detector

     
    • Phase sequence and open phase check
    • Large size alligator clips
    Add To Quote
  • KS3 3PHASE DETECTOR – SANWA

    Motor rotation direction testable before connection of the power supply.

    • Safety design that complies with IEC61010-1 CAT. III 500 V.
    • Motor rotation direction testable before connection of the power supply.
    • Phase sequence and open phase checking of three-phase lines.
    • Bright LED indicators.
    • Magnets on the back of the main unit allow it to be fixed on a distribution board and other metallic objects.
    Add To Quote
  • LCR 700 LCR METER – SANWA

    Handheld Digital LCR meter

    LCR700 is a full-featured high-performance handy LCR meter which rivals the capabilities and options of many of its bench counterparts. This instrument features a device value sorting function, allowing users to quickly sort passive devices in situations such as incoming inspections.

    • Automatically selectable L/C/R measurement and Selectable Series/Parallel mode
    • Ls/Lp/Cs/Cp measurement with sub parameters (D/Q/θ/ESR)
    • 5 different measuring frequencies (100/120/1k/10k/100kHz)
    • DC resistance function (7 ranges: 200.00Ω to 200.0MΩ)
    • 5-terminal measurement (4 terminals plus guard shielding)
    • Device Sorting mode to allow users to quickly sort passive devices such as L, C, and R
    Add To Quote
  • LP 1 LASER POWER METER – SANWA

    Laser power meter

    Optical power up to max. 40mW measurable   Direct reading wavelength customization
    NOTE: This item has been discontinued by SANWA. The replacement for this item is LP10
    Add To Quote
  • LP10 – Laser Power Meters – SANWA

    Laser Power Meter

    Measurement range (CW laser): 0.01μW~40.39mW
    Customization of wavelength to 400 ~ 1100 nm is available by factory default setting.

    NOTE: if you are looking for LP1, please note that SANWA has discontinued that model and its been upgraded/replaced with LP10.  Contact us at info@bhumika.ca for more info and relevant differences.

    • Pocket size.
    • Separate light sensor probe can be integrated with the main body for measurement.
    • 4039 full-scale count with a bar graph display.
    • Direct reading of the laser power of the reference wavelength of 633 nm, while the laser power of other wavelengths can be read by converting it according to the spectral sensitivity characteristic table.
    • Wide measuring range from 0.01 μW to 40.39 mW.
    • MIN/MAX hold functions.
    • The diffusion sheets are used in the sensor, it can suppress the “return light” that is generated when a laser light enters the sensor.
    • Auto power save function prevents wasting of battery power.
    Add To Quote
  • LX20 – Illuminance Meter – SANWA

    Stick-shaped small light sensor (window diameter 9 mm) for narrow position or area

    • Easy-to-carry pocket size.
    • Separate, stick-shaped light sensor (window diameter 9 mm) from the main body enables measurement of a narrow position or area. The light sensor can also be integrated with the main body for measurement.
    • 4039 full-scale count with a bar graph display.
    • Improved measurement accuracy by using a silicon photodiode, which has a spectral sensitivity approximating the relative luminous efficiency specified by CIE (Commission Internationale d’Eclairage), in the light sensor.
    • Wide measuring range of 0.1 lx to 403.9 klx (403,900 lx).
    • Data hold function.
    • Auto power save function prevents wasting of battery power.
    Add To Quote
  • M53 INSULATION TESTER – SANWA

    Digital for Elevator maintenance

    2 test voltage ranges, for Elevator maintenance

    • 500V; 200MΩ
    • 15V; 20MΩ
    • Auto range
    • Auto power off(1min.)
    • Low battery power indication
    • Remote speed measurement(Speed meter SE9100 is necessary.)
    Add To Quote
  • MG 500 INSULATION TESTER – SANWA

    Dustproof / splashproof(IP54) design

    • 500V; 4000MΩ
    • 250V; 4000MΩ
    • 125V; 4000MΩ
    • Hot-line state (30V minimum) detection
    • Large volt mark with the buzzer sound
    • Automatic data hold function
    • Bar graph just like analog meter
    • Large display with backlight
    • Easy to use & tough body
    • IP54
    • Continuity test(200mA) function
    Add To Quote
  • MG1000 INSULATION TESTER – SANWA

    Digital 3 ranges

    Automatic determination of the live state of the measurement line

    • 1000V; 4000MΩ
    • 500V; 4000MΩ
    • 250V; 4000MΩ
    • Hot-line state(30V minimum) detection
    • Large volt mark with the buzzer sound
    • Automatic data hold function
    • Bar graph just like analog meter
    • Large display with backlight
    • Easy to use & tough body
    • IP54
    • Continuity test(200mA) function
    Add To Quote