EM7000 ANALOG MULTITESTER – SANWA
High sensitivity for measurement of lower capacitance
- High-sensitivity FET electronic tester with high input resistance (2.5M – 12MΩ for DCV) and 0.12μA range (DC current)
- Frequency response against 40Hz to 1MHz of sine wave (AC low voltage)
- Measurement of P-P value (Peak to Peak value) of square wave pulse (duty cycle 20% or higher)
- Wide range resistance measurement from 0.2Ω to 200MΩ
※Zero adjustment needs to be performed before measurement, since the instrument is an electronic tester.
Analog Multitesters FET Tester
High sensitivity for measurement of lower capacitance
BASIC FEATURES:
- High input impedance (DCV2.5〜12MΩ/V), and 0.12μA range (DCA)
- Bandwidth 40Hz〜1MHz AC sign wave
- Rectangular pulse P-P (Peak to Peak) measurement (duty cycle 20% and above)
- Wide ohm range 0.2Ω〜200MΩ
- Bandwidth : 40Hz〜1Mhz (12V range and below)
SAFETY:
IEC61010-1 (EN61010-1) 2001-02 CAT.III 600V Max.
OPTIONAL ACCESSORIES:
HV probe : HV-60
Carrying case : C-CA
Clip adapter : CL-11, CL-13, CL-15a, CL-DG3a, TL-8IC
Test lead : TL-21M, TLF-120
| Function | Measuring range | Tolerance |
|---|---|---|
| DCV | 0.3/1.2/3/12/30/120/300/1000V（2.5～12MΩ) | ±3% of full scale |
| ±DCV | ±0.15/0.6/1.5/6/15/60/150/600V（2.5～12MΩ) | ±7% of full scale |
| AC voltage rms(50/60Hz) | 3V（approx.2.5MΩ）/12V（approx.1.1MΩ） 30V/120/300V（approx.800KΩ）/750V（approx.10MΩ) | ±3% of full scale |
| ACV P-P |
Sine wave – 8.4V（approx.2.5MΩ/V）/33V（approx.1.1MΩ） 84/330/840V（approx.800KΩ) | ±5% of full scale |
| ACV P-P |
Square wave – 8.4V（2.5MΩ) | ±6% of full scale |
| ACV P-P |
Triangle wave – 8.4V（2.5MΩ) | ±6% of full scale |
| DCA | 0.12μ/0.3m/3m/30m/300m/6A | ±3% of full scale |
| DCA | ±0.06μ/±0.15m/1.5m/15m/150mA | ±7% of full scale |
| ACA | 6A | ±5% of full scale |
| Resistance | 2k/20k/200k/2M/20M/200MΩ | ±3% of arc |
| Low-frequency output | -10～51dB | ±3% of arc |
| Frequency characteristic | AC12V range or lower 40Hz to 1 MHz: frequency response within ±5% |
| Battery | R6P(AA battery)1.5Vx2, 6F22(9V manganese battery)x1 |
| Built-in fuse | F1176 Φ5×20mm 0.5A/250V 1.5kA Ceramic fuse F1177 Φ5×20mm 6.3A/250V 1.5kA Ceramic fuse |
| Size/Mass | H165×W106×D46mm/Approx. 375g |
※The value in ( ）at DCV and ACV is input resistance
Related products
-
AU-32 / AU-31 ANALOG MULTITESTER – SANWA
Add To QuoteAU-32 / AU-31 Analog Multitesters High input impedance Auto range, High input impedance BASIC FEATURES: Auto range selection (V, Ω) Auto polarity High input impedance 1〜10MΩ Series capacitor input ※AU-31 ACV only Auto 0Ω adjustment Inner battery check DC / AC auto selection ※AU-32 only 5 ranges DC / AC current ※AU-32 only Bandwidth : …
-
SP – 18D ANALOG MULTITESTER – SANWA
Add To QuoteCase and instrument in one body, that brings you a convenience to carry and store
- Resistance up to 200MΩ can be measured under the low voltage(3V)
- Capacitance measurement from 0.01μF to 1000μF
- Resistance measurement that has 3V of the terminal voltage allows to check an LED
- Battery check
- Front panel protection cover that also works as a stand
-
AP 33 ANALOG MULTITESTER – SANWA
Add To QuotePocketable Analog Multimeter / Analog Multitester
- Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
- The test leads can be winded up and stored
- Battery check function has 2 ranges of 1.5V/9V
- Shock absorbing rubber that is robust against falling
-
SP21 ANALOG MULTITESTER – SANWA
Add To QuoteShockproof meter
With continuity check beeper
- Employs shockproof taut-band meter that is not easily damaged even if dropped
- Zero center meter for ± DCV measurement
- Double protection with fuse and diode to protect the internal circuit from overvoltage
- Battery check
- With a tilt stand that helps to read the meter
-
YX – 361TR ANALOG MULTITESTER – SANWA
Add To QuoteVariety of measurement functions by using 24-contact switch
- Employing 24-contact switch and plus alpha function enable you to enjoy a total of 33 functions
- Zero center meter for ± DCV measurement
- With LED for continuity check
- With OUTPUT measurement terminal (series capacitor inserted)
- Battery check
- DC current gain (hFE) of transistor can be measured by using separately available hFE connector
