Category
VS – 100 ANALOG MULTITESTER – SANWA
Employs current-limiting fuse with 100kA of breaking current
- Tester for maintenance and management for electrical equipment that is suitable for measuring high-power low-voltage circuits(500V or lower)
- Built-in current-limiting fuse cuts off the current at 100kA to reduces the risk of arc discharge
- Hard case included
Analog Multitesters For power line
Current-limiting fuse, 100kA breaking capacity, is installed.


BASIC FEATURES:
- For lower voltage circuit (500V and below) with large capacitance
- Current-limiting fuse that can interrupt 100kA, is installed.
- All renges are protected from input voltage upto 500V
- Carrying case
- Bandwidth : 40〜10kHz (50V and below)
SPECIFICATIONS:
Function | Measuring range | Tolerance |
---|---|---|
DCV | 10/50/250/500V(4kΩ/V) | ±3% of full scale |
ACV | 10/50/250/500V(4kΩ/V) | ±3% of full scale |
Resistance | 2k/20k/2MΩ | ±3% of arc |
Frequency characteristic | AC50V range or lower 40Hz to 10kHz: frequency response within ±3% |
Battery | R6P(AA battery)1.5Vx2 |
Built-in fuse | F0304 Φ13x50mm 3A/600V 100kA D-type fuse F0314 Φ6.3x30mm 0.25A/250V 100A Ceramic fuse |
Size/Mass | H144×W96×D56mm/Approx. 395g |
※The value in ( ) at DCV and ACV is input resistance
Category: Analog Multitesters
Related products
-
AU-32 / AU-31 ANALOG MULTITESTER – SANWA
Add To QuoteAU-32 / AU-31 Analog Multitesters High input impedance Auto range, High input impedance BASIC FEATURES: Auto range selection (V, Ω) Auto polarity High input impedance 1〜10MΩ Series capacitor input ※AU-31 ACV only Auto 0Ω adjustment Inner battery check DC / AC auto selection ※AU-32 only 5 ranges DC / AC current ※AU-32 only Bandwidth : …
-
CX 506a ANALOG MULTITESTER – SANWA
Add To QuoteCapacitance measurement function with built-in transistor oscillator
- Variety of measurement functions by using 26-contact switch
- Capacitance measurement from 50pF to 2000μF
- High input resistance 50kΩ/V (each range of DC3 to 300V)
- DC polarity switchable
-
SP21 ANALOG MULTITESTER – SANWA
Add To QuoteShockproof meter
With continuity check beeper
- Employs shockproof taut-band meter that is not easily damaged even if dropped
- Zero center meter for ± DCV measurement
- Double protection with fuse and diode to protect the internal circuit from overvoltage
- Battery check
- With a tilt stand that helps to read the meter
-
SP – 18D ANALOG MULTITESTER – SANWA
Add To QuoteCase and instrument in one body, that brings you a convenience to carry and store
- Resistance up to 200MΩ can be measured under the low voltage(3V)
- Capacitance measurement from 0.01μF to 1000μF
- Resistance measurement that has 3V of the terminal voltage allows to check an LED
- Battery check
- Front panel protection cover that also works as a stand
-
AP 33 ANALOG MULTITESTER – SANWA
Add To QuotePocketable Analog Multimeter / Analog Multitester
- Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
- The test leads can be winded up and stored
- Battery check function has 2 ranges of 1.5V/9V
- Shock absorbing rubber that is robust against falling