SP – 18D ANALOG MULTITESTER – SANWA
Case and instrument in one body, that brings you a convenience to carry and store
- Resistance up to 200MΩ can be measured under the low voltage(3V)
- Capacitance measurement from 0.01μF to 1000μF
- Resistance measurement that has 3V of the terminal voltage allows to check an LED
- Battery check
- Front panel protection cover that also works as a stand
Analog MultitestersDrop shock proof meter
Protective body cover
BASIC FEATURES:
- Low power ohm (3V) measurement upto 200MΩ
- Capacitance measurement 0.01μF〜1000μF
- LED check by 3V terminal voltage at resistance range
- Battery check
- Protective body cover
- Bandwidth : 30〜80kHz (AC12V), 30〜20kHz (AC30V)
OPTIONAL ACCESSORIES:
Clip adapter : CL-11, CL-15a, CL-DG3a, TL-8IC
SPECIFICATIONS:
| Function | Measuring range | Tolerance |
|---|---|---|
| DCV | 0.3（5kΩ）/3/12/30/120/600V（20kΩ/V) | ±3% of full scale |
| ACV | 12/30/120/300/600V（9kΩ/V) | ±3% of full scale |
| DCA | 60μ/30m/0.3A | ±3% of full scale |
| Resistance | 2k/20k/2M/200MΩ | ±3% of arc (200MΩ:±5% of arc) |
| Battery check | 1.5V/1.5V button battery | ̶ |
| Capacitance | 1000μF | Approximate value |
| Frequency characteristic | AC12V range 30Hz to 70kHz, AC30V range 30Hz to 20kHz: frequency response within ±3% |
| Battery | R6P(AA battery) 1.5Vx2 |
| Built-in fuse | F0301 Φ5x20mm 0.5A/250V 300A Glass fuse |
| Size/Mass | H159.5×W129×D41.5mm/Aprprox. 320g |
| Test lead length/Pin tip | Length Approx. 0.9m/19mm |
※The value in （ ）at DCV and ACV is input resistance
Related products
-
SP21 ANALOG MULTITESTER – SANWA
Add To QuoteShockproof meter
With continuity check beeper
- Employs shockproof taut-band meter that is not easily damaged even if dropped
- Zero center meter for ± DCV measurement
- Double protection with fuse and diode to protect the internal circuit from overvoltage
- Battery check
- With a tilt stand that helps to read the meter
-
AP 33 ANALOG MULTITESTER – SANWA
Add To QuotePocketable Analog Multimeter / Analog Multitester
- Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
- The test leads can be winded up and stored
- Battery check function has 2 ranges of 1.5V/9V
- Shock absorbing rubber that is robust against falling
-
YX – 361TR ANALOG MULTITESTER – SANWA
Add To QuoteVariety of measurement functions by using 24-contact switch
- Employing 24-contact switch and plus alpha function enable you to enjoy a total of 33 functions
- Zero center meter for ± DCV measurement
- With LED for continuity check
- With OUTPUT measurement terminal (series capacitor inserted)
- Battery check
- DC current gain (hFE) of transistor can be measured by using separately available hFE connector
-
CP – 7D ANALOG MULTITESTER – SANWA
Add To QuoteWide scale with mirror for easy reading of measured values
- Wide scale with mirror
- Fixed test leads for safety and operability
- Employs metal oxide film resistors that are high precision, heat resistant, smokeless
- Battery check
- Internal circuit protection with fuse and diode
-
VS – 100 ANALOG MULTITESTER – SANWA
Add To QuoteEmploys current-limiting fuse with 100kA of breaking current
- Tester for maintenance and management for electrical equipment that is suitable for measuring high-power low-voltage circuits(500V or lower)
- Built-in current-limiting fuse cuts off the current at 100kA to reduces the risk of arc discharge
- Hard case included
