SP20 ANALOG MULTITESTER – SANWA
Shockproof meter
Provides DC high voltage and temperature measurement
- Has 20 measurement functions to cover general measurement applications
- 500μF capacitor check function
- With a tilt stand that helps to read the meter
- Provides DC high voltage and temperature measurement with separately available accessory
- Battery check
SP20
Analog Multitesters Drop shock proof meter
DC high volotage & temperature measurable
BASIC FEATURES:
- 20ch measurement ranges
- Capacitance measurement 500μF
- Tilt stand
- DC high voltage and temperature measurement (with optional accessories)
- Bandwidth : 40〜100kHz (AC10V)
SPECIFICATIONS:
| Function | Measuring range | Tolerance |
|---|---|---|
| DCV | 0.25/2.5/5/10/50/100（20kΩ/V）/500V（9kΩ/V) | ±3% of full scale |
| ACV | 10/50/250/500V（9kΩ/V) | ±3% of full scale |
| DCA | 50μ/2.5m/25m/0.25A | ±3% of full scale |
| Resistance | 2k/20k/200k/2MΩ | ±3% of arc |
| Capacitance | 500μF | Approximate value |
| DC high voltage | DC25kV (Using separately available probe HV-10) | ±20% with probe |
| Temperature | -20 to + 200℃ (Using separately available probe T-THP) | ±3% (Using T-THP) |
| Battery check | 1.5V (1.0～2.0V) | Approximate value |
| Frequency characteristic | AC10V range 40Hz to 100kHz: frequency response within ±3% |
| Battery | R6P(AA battery)1.5Vx2 |
| Built-in fuse | F0305 Φ6.3x30mm 0.5A/250V 300A Glass fuse |
| Size/Mass | H144×W99×D41mm/Approx. 270g |
※The value in （ ）at DCV and ACV is input resistance
OPTIONAL ACCESSORIES:
HV probe : HV-10
Temperature probe : T-THP
Carrying case : C-SPH or C-SP
Clip adapter : CL-11, CL-15a, CL-DG3a, TL-8IC
Test lead : TL-91M, TLF-120
Related products
-
YX – 361TR ANALOG MULTITESTER – SANWA
Add To QuoteVariety of measurement functions by using 24-contact switch
- Employing 24-contact switch and plus alpha function enable you to enjoy a total of 33 functions
- Zero center meter for ± DCV measurement
- With LED for continuity check
- With OUTPUT measurement terminal (series capacitor inserted)
- Battery check
- DC current gain (hFE) of transistor can be measured by using separately available hFE connector
-
AU-32 / AU-31 ANALOG MULTITESTER – SANWA
Add To QuoteAU-32 / AU-31 Analog Multitesters High input impedance Auto range, High input impedance BASIC FEATURES: Auto range selection (V, Ω) Auto polarity High input impedance 1〜10MΩ Series capacitor input ※AU-31 ACV only Auto 0Ω adjustment Inner battery check DC / AC auto selection ※AU-32 only 5 ranges DC / AC current ※AU-32 only Bandwidth : …
-
EM7000 ANALOG MULTITESTER – SANWA
Add To QuoteHigh sensitivity for measurement of lower capacitance
- High-sensitivity FET electronic tester with high input resistance (2.5M – 12MΩ for DCV) and 0.12μA range (DC current)
- Frequency response against 40Hz to 1MHz of sine wave (AC low voltage)
- Measurement of P-P value (Peak to Peak value) of square wave pulse (duty cycle 20% or higher)
- Wide range resistance measurement from 0.2Ω to 200MΩ
※Zero adjustment needs to be performed before measurement, since the instrument is an electronic tester.
-
AP 33 ANALOG MULTITESTER – SANWA
Add To QuotePocketable Analog Multimeter / Analog Multitester
- Employs test leads woven with nylon. Reduces the possibility of wire damage due to winding and pulling
- The test leads can be winded up and stored
- Battery check function has 2 ranges of 1.5V/9V
- Shock absorbing rubber that is robust against falling
-
VS – 100 ANALOG MULTITESTER – SANWA
Add To QuoteEmploys current-limiting fuse with 100kA of breaking current
- Tester for maintenance and management for electrical equipment that is suitable for measuring high-power low-voltage circuits(500V or lower)
- Built-in current-limiting fuse cuts off the current at 100kA to reduces the risk of arc discharge
- Hard case included
